Looking for Paving Repair Hitchin?

If you are looking for paving repair Hitchin, Creative Cobblestones are experts in all types of paving repair – driveway repair, path repair, patio repair. We have many years of paving repair experience with all types of paving including:

 

Paving repair to Block Paving
Paving Repair to Tarmac
Paving Repair to Concrete
Paving Repair to Pattern Imprinted Concrete
Paving Repair to Paving Slabs

 

Block Paving Repair Hitchin

Block Paving Repair Hitchin

If you have an area of your block paving driveway which has sunk or been disturbed by tree roots, we can help. We start by removing one single block or brick to allow access and then we can remove however many blocks required to make the repair. If you are attempting the repair to the block paving yourself, there are two simple methods for removing this first block. Firstly and the ideal method, use two tools such as a trowel or similar inserted at opposite ends of the block and gently ease the block upwards until it can be completely removed from the rest of the block paving. This first block should be undamaged by the process and can be used again when relaying the block paving after the repair. If for some reason this method doesn’t work, the only option is to use a sharp chisel to break one block and lift the broken sections away giving access to the rest of the block paving. Obviously this first block would be thrown away as unusable.

If we were to carry out the repair, we have a tool called a block extractor which makes the process very simple indeed and causes no damage to any of the blocks.

Once the first block has been removed, we can remove the adjacent ones by levering underneath each block. Then we remove as many of the blocks needed to make the repair. The blocks are brushed, cleaned and retained close-by for re-use. Once any problems are resolved, e.g. tree roots removed and dips filled up, we then treat the bedding area as needed to prepare for the relay ensuring the correct height is achieved to allow for compaction of the salvaged blocks as a guide. Leave the bedding approximately 5mm high to allow for re-compaction.

We then replace the blocks in the repair area and reseal with appropriate joints using a plate compactor to complete the job.

The only issue which may arise is colour matching. If you still have some spare blocks from when the block paving was originally laid, we can use those to replace any damaged blocks. If you don’t have any originals, we would normally take up say twice the number of blocks needed for the repair and mix and match the existing blocks with new ones to make the repair less obvious With time the original blocks and the new replacements will look the same.

 

Tarmac Paving Repair Hitchin

Because tarmac is not a modular material it can only be patch repaired which is impossible to disguise unfortunately as the patch cannot be matched colour wise.

The best you can hope for is that the supplier you originally used can tell you exactly what materials where used to enable you to get the paving repair as close as possible to the original.

How we repair tarmac

We mark out the area to be treated and use specialist tools to cut the surface area allowing us to remove the damaged material and dispose of it. We coat the edges of the cut area with a jointing compound to ensure water resistance and lay fresh tarmac usually in two layers compacting each payer as we go.

We always cover or fence off wet concrete to ensure no stray foot prints or paw prints on the new surface. The repair can usually be back in use after a few days.

 

Concrete Paving Repair Hitchin

The best way to repair even the tiniest cracks in concrete is to make the cracks bigger.

We use a specialist concrete breaker to open the crack so it is about 25-50mm wide and at least 75mm deep.

We then clean up the area by sweeping out the dust and bits of concrete. We need to make sure this is done thoroughly as even a tiny piece of concrete left in the crack will prevent the epoxy mortar from bonding to the entire surface area of the crack. This could render the repair useless. Once it is cleaned up and all the damaged area removed, we apply the mortar appropriately.

The area of repair will be completely waterproof and will withstand pretty much any temperatures without crumbling. The area will be ready for traffic after about 4 hours and is fully cured after 24 hours.

Pattern Imprinted Concrete Paving Repair Hitchin

Pattern imprinted concrete is extremely hardwearing and doesn’t require a lot up upkeep – one of its advantages over other paving solutions.

There are times, however, when you need a repair – typically after a new building project when part of the patio or driveway has been removed to accommodate an extension or if you’ve had gas pipes or water pipes repaired. The repair is done to ensure the new section matches the existing colour and pattern and can be competed relatively quickly.

Pattern imprinted concrete needs to be resealed every 3 – 5 years to ensure that it stays looking good. Quite often people do not realise this; they may have inherited a pattern imprinted concrete driveway when they moved into the house or the contractor who laid it did not inform them of this requirement.

As the saying goes, prevention is better than cure and so it is with pattern imprinted concrete. You should have your driveway or patio resealed on a regular basis to ensure that it stays looking good and retains its good looks.

A reseal involves firstly cleaning the area and preparing it for the appropriate treatment whether clear or tinted seal is to be used. Any cracks will be repaired and then once the area is dry it will be sealed with a compound which also includes a non-slip element to increase safety.

Paving Slab Repair Hitchin

As paving slabs are a modular paving solution they can be repaired relatively easily i the same way as block paving as described above.

It’s common for a section of paving or even a single slab to sink because of ground movements, tree roots or heavy use, and this can make rainwater collects in puddles.

To repair the damaged paving we would chip out the pointing around the slab and then remove the slab with a spade, using a a piece of wood to protect the slab next to it. Once the slab was removed, we would break up and remove the old mortar and add sand as required to level the area. If the slab was originally laid on mortar, we would add a fresh bad of mortar and lay the new slab in position ensuring it’s in line with the surrounding slabs. Once in position, we would fill the joints with dry mortar.


Areas we cover: